The Saab Link Forums - Search Results

Go Back   The Saab Link Forums > Search Forums

SaabLink.net is the premier Saab Forum on the internet. Registered Users do not see the above ads.
Showing results 1 to 7 of 7
Search took 0.00 seconds.
Search: Posts Made By: The Geek Group SAAB Guy
Forum: Car Problems? 9-5 Only 11-13-2016, 12:20 PM
Replies: 3
Views: 540
Understood. I get it now. I just wish, before I...

Understood. I get it now. I just wish, before I ripped the engine out, someone had explained it in these terms in a cylinder head overhaul guide. Then, I would have KNOWN:

"I must warn you that...
Forum: Car Problems? 9-5 Only 10-31-2016, 12:46 PM
Replies: 3
Views: 540
Rough running after cylinder head overhaul

Any ideas why my engine sounds like this?

I have the engine out and I'm about to do the timing and balance chains. I think.

https://www.dropbox.com/s/vpaxjicfrjm6554/IMG_5328.MOV?dl=0
Forum: General NG900 / Old 9-3 Posts and Information 10-23-2016, 04:36 AM
Replies: 23
Views: 14,390
I removed the snap ring, but where the shaft came...

I removed the snap ring, but where the shaft came apart was at the tripod bearing. Where else is it going to separate? Near the snap ring or does the whole long shaft pull out of the trans on the...
Forum: General NG900 / Old 9-3 Posts and Information 10-23-2016, 03:40 AM
Replies: 23
Views: 14,390
Thanks to all! Great ideas and I tried 'em all....

Thanks to all! Great ideas and I tried 'em all. Nothing. Then I went to a buddys shop the other day, he asked me to unplug an air line, and it almost took my nose off. Suddenly, it dawned on...
Forum: General NG900 / Old 9-3 Posts and Information 10-10-2016, 08:17 PM
Replies: 23
Views: 14,390
More heat, no progress. When you say heat/cool,...

More heat, no progress. When you say heat/cool, do you mean I should quench with cold water after heating and before trying to loosen? I HAVE to get these nuts off to remove my engine. Storage is...
Forum: General NG900 / Old 9-3 Posts and Information 10-09-2016, 12:05 PM
Replies: 23
Views: 14,390
Ok. So far, my cycle has been PB, air impact...

Ok. So far, my cycle has been PB, air impact ratchet, heat, air impact ratchet, heat, repeat, repeat, repeat. Finally, after heating it, I tried a long breaker bar on the socket. I smashed/bloodied...
Forum: General NG900 / Old 9-3 Posts and Information 10-07-2016, 10:53 AM
Replies: 23
Views: 14,390
Drive shaft removal? I should be so lucky. How...

Drive shaft removal? I should be so lucky. How did you remove the two rustiest nuts on the car? (On the outside ends of the shafts) Mine are rusted on and partially disintegrated.
Showing results 1 to 7 of 7

 
Forum Jump

All times are GMT -8. The time now is 10:09 PM.


Powered by vBulletin® Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.5.2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
All content is copyright The Saab Link and it's original authors.


 

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.