The Saab Link Forums - Reply to Topic

Go Back   The Saab Link Forums > Saab NG900 '94-'98 and 9-3 '99-'02 Forum > N/A Performance Modifications for the NG900 / Old 9-3 > Couple days of dyno time on the 2.3Na car..

N/A Performance Modifications for the NG900 / Old 9-3 This forum contains PERFORMANCE related Q&A's specific to NATURALLY ASPIRATED NG900 and old 9-3.

SaabLink.net is the premier Saab Forum on the internet. Registered Users do not see the above ads.
Thread: Couple days of dyno time on the 2.3Na car.. Reply to Thread
Title:
  
Message:
Trackback
Send Trackbacks to (Separate multiple URLs with spaces):
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Saab Link Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Vehicle Info.
Enter your vehicle information (year, model, mods)
Insurance
Please select your insurance company (Optional)

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-23-2008 01:58 PM
moose
Quote:
Originally Posted by GenuineSaab View Post
Only need a trionic harness...
sounds like you need to hit up a junkyard.
05-23-2008 01:54 PM
GenuineSaab Takes me about a minute to change the cam timing.. Maybe 30 times in the past couple days.. Done now till I get trionic. I am too stuck with stock timing and cant optimize it for my new flow. Tried lying to it with load (70mm vs 60mm maf) scaling to get back into the middle of the timing map it makes a mess of fuel / timing on low loads when I get enough injector to keep it reasonably near LBT

Only need a trionic harness...
05-23-2008 01:33 PM
spgproject
Quote:
Originally Posted by jonny72888 View Post
cant all of that be done with a tune?
No.
05-23-2008 01:31 PM
jonny72888 cant all of that be done with a tune?
05-23-2008 11:37 AM
JZW He does it the same way the swedes do and what many do in place of adjustable cam gears. You just remove the keyway, put the cams wherever you want and lock them down to 50 ft-lbs with lock tight on the bolt.

I ran my enem cams this way for 2 months before putting on the maptun cam gears, or speed parts. The stock cam gears are much easier to work with and much easier to adjust.

I had a hell of a time getting the speed parts adjustable cam gears to line up right and stay there while you tightened the 6 allen bolts and main cam gear bolt down. Took my 6 hours in all The stock cam gears with removed key-way took me about 2 hours to get dialed in and perfect when it was all tight.

John
05-23-2008 03:52 AM
spgproject are you notching the cams or something? you mentioned playing with cam timing.
05-23-2008 03:48 AM
SAABOOST Nice! Me likes, but not till next year.
05-22-2008 06:27 PM
Green9kAERO looks like shes going pretty good.

i find this car more interesting then many of the FI cars we are building. i do not know why
JP
05-22-2008 05:05 PM
Palmer Nice.

I like the 9-3 front end SO much better than the NG.

Also, nice grillE.
05-22-2008 03:27 PM
viggenkid looking good
05-22-2008 03:26 PM
imheretostay I like the color scheme going for you.... maybe do a gray and red stripe all the way from the front to the rear along the center line of the car hood, roof, to trunk. After you do this and see the results... might you try and lower the compression, maybe even see if its possible to run an LPT header and a standalone boost controller?
05-22-2008 03:16 PM
GenuineSaab Well it is officially now the Black, Silver and Red car.. 9-3Se skirts.

V6 maf housing rigged in.. The wires were cut in the crash before we got it.


Head off in 1.5hr.. Not super fast but hey..


Going to grind a little on the head too. Will find out how it puts out by noon tomorrow.
05-22-2008 01:56 PM
Palmer ^yeah, no doubt.


Keep us posted!
05-22-2008 01:56 PM
jonny72888 this is why i went from N/A to FI.
i had a 2.0 jetta. 272cam, duel valve springs,flywheel, chip, underdrive pulleys, adjustable cam gears, header, full exhaust, thin head gasket. = 43whp i got about 6mpg more so thats good.


so nick how long intil you have all those parts made for the n/a 2.3?
05-22-2008 01:41 PM
nowhereman good luck i am sure there are a lot of 900S etc owners on here dying for what you come up with.
05-22-2008 01:39 PM
GenuineSaab
Couple days of dyno time on the 2.3Na car..

Well thought it time to post preliminary info on what I have been playing with on my 2.3i shop car.
Some Highlights:
Inlet manifold swap to short runner turbo for more topend, lost midrange.
Cam timing both intake and exhaust. Can vary power all over the place.
V6 maf swap 60mm > 70mm diameter. Not right but works 50%
T5 Injector to make the above work, increased fuel press 3.5/4.0 maybe.


I will get some plots up sometime. Some worked some didn't.

Tonight head comes off, switching to B2x5 thinner headgasket = more compression and while the head is off going to throw a t7 head with the same 234i cams just to see.


Maybe then my T5 harness will be here and I can get to actually calibrating it rather than swapping airflow parts.

Making N/A power is quite challenging and lots of fun! No 50hp gains here.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -8. The time now is 01:00 AM.


Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.5.2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
All content is copyright The Saab Link and it's original authors.


 

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.