Saab 9000 Recall List - 1986 -1998 - The Saab Link Forums

Go Back   The Saab Link Forums > Saab 9000 Forum > General 9000 Posts and Information

General 9000 Posts and Information Please post general information pertaining to the Saab 9000.

SaabLink.net is the premier Saab Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools
Old 10-27-2010, 06:28 AM   #1
Elder
 
BurnsSide42's Avatar
 
Join Date: Oct 2003
Location: South Eastern PA
Posts: 10,049
Post Saab 9000 Recall List - 1986 -1998

1986 Saab 9000 Recalls:

Item Affected: ELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH
Date Announced: 10/29/1986

Description of Recall:
THE WIRING HARNESS MAY CHAFE AGAINST THE WINDSHIELD WIPER MOTOR BRACKET. CONSEQUENCE OF DEFECT: IF A SHORT CIRCUIT DEVELOPS, IT COULD RESULT IN A FIRE.

Action Needed To Fix It:
AFFIX TWO RUBBER STRIPS TO THE VERTICAL EDGES OF THE WINDSHIELD WIPER MOTOR BRACKET.
------------------------------------------------
Item Affected: ELECTRICAL SYSTEM:IGNITION:SWITCH
Date Announced: 1/16/1990

Description of Recall:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.

Action Needed To Fix It:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.



1987 Saab 9000 Recall:

Item Affected: ELECTRICAL SYSTEM:IGNITION:SWITCH
Date Announced: 1/16/1990

Description of Recall:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.

Action Needed To Fix It:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.



1988 Saab 9000 Recalls:

Item Affected: VEHICLE SPEED CONTROL
Date Announced: 4/12/1988

Description of Recall:
THE BALL CHAIN BETWEEN THE CRUISE CONTROL VACUUM REGULATOR AND THE ACCELERATOR PEDAL ARM MAY CATCH ON THE VACUUM REGULATOR ATTACHMENT CLIP.

Action Needed To Fix It:
A PLASTIC CAP WILL BE INSTALLED OVER THE VACUUM REGULATOR CLIP TO COVER THE OPENINGS.

-----------------------------------------------
Item Affected: ELECTRICAL SYSTEM:IGNITION:SWITCH
Date Announced: 1/16/1990

Description of Recall:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.

Action Needed To Fix It:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.

-------------------------------------------------
Item Affected: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS
Date Announced: 11/28/1989

Description of Recall:
THE ROUTING OF THE THROTTLE KICKDOWN CABLE COULD ALLOW CHAFING TO OCCUR BETWEEN THE CABLE AND ANY ONE OF THREE STEEL BRAKE FLUID LINES NEAR THE VALVE BLOCK OF THE HYDRAULIC BRAKE UNIT.

Action Needed To Fix It:
CHANGE CABLE ROUTING AND INSTALL NEW ATTACHMENT BRACKET TO PREVENT CHAFING.


1989 Saab 9000 Recalls:

Item Affected: ELECTRICAL SYSTEM:IGNITION:SWITCH
Date Announced: 1/16/1990

Description of Recall:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.

Action Needed To Fix It:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.

-----------------------------------------------
Item Affected: FUEL SYSTEM, GASOLINEELIVERY:HOSES, LINES/PIPING, AND FITTINGS
Date Announced: 12/6/1988

Description of Recall:
FUEL FILTER MAY NOT MEET THE SPECIFICATION CONCERNING LEAKAGE CRITERIA DUE TO LOW TEMPERATURE DURING THE GLUING PROCESS.

Action Needed To Fix It:
REPLACE FUEL FILTER.

------------------------------------------------
Item Affected: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS
Date Announced: 11/28/1989

Description of Recall:
THE ROUTING OF THE THROTTLE KICKDOWN CABLE COULD ALLOW CHAFING TO OCCUR BETWEEN THE CABLE AND ANY ONE OF THREE STEEL BRAKE FLUID LINES NEAR THE VALVE BLOCK OF THE HYDRAULIC BRAKE UNIT.

Action Needed To Fix It:
CHANGE CABLE ROUTING AND INSTALL NEW ATTACHMENT BRACKET TO PREVENT CHAFING.



1990 Saab 9000 Recall:

Item Affected: ELECTRICAL SYSTEM:IGNITION:SWITCH
Date Announced: 1/16/1990

Description of Recall:
ABRASION ON THE PRINTED CIRCUIT CARD IN THE COMBINATION NEUTRAL SAFETY/BACKUP LAMP SWITCH OPERATED BY THE AUTOMATIC TRANSMISSION GEAR SELECTOR MAY CAUSE RESIDUE TO COLLECT IN ELECTRICAL AREA ON THE CIRCUIT CARD.

Action Needed To Fix It:
ADD AN ELECTRICAL CIRCUIT, INCLUDING A RELAY, TO THE BACKUP LAMP CIRCUIT TO REDUCE THE CURRENT THAT CAN FLOW THROUGH THE COMBINATION SWITCH.



1991 Saab 9000 Recall:

Item Affected: POWER TRAIN:AUTOMATIC TRANSMISSION
Date Announced: 1/15/1991

Description of Recall:
IMPROPER ASSEMBLY COULD CAUSE THE BALL OF THE GEAR SELECTOR ARM NOT TO BE PROPERLY FIXED TO THE SOCKET ON THE END OF THE GEAR SELECTOR CABLE; GEAR SELECTOR ARM COULD SEPARATE FROM THE GEAR SELECTOR CABLE AT THE BALL SOCKET JOINT.

Action Needed To Fix It:
PROPERLY SEAT GEAR SELECTOR ARM BALL IN THE SELECTOR CABLE SOCKET AND SECURE BY A LOCK RING INSIDE THE SOCKET.



1992 Saab 9000 Recalls:

Item Affected: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE
Date Announced: 5/12/1999

Description of Recall:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. MOISTURE CAN ENTER THE AIR BAG INFLATABLE RESTRAINT ELECTRONIC CONTROL MODULE (ECM) AND CAUSE CORROSION ON PORTIONS OF THE ECM PRINTER CIRCUIT BOARDS.

Action Needed To Fix It:
DEALERS WILL INSPECT THE EXTERIOR OF THE ECM. IF THERE IS NO INDICATION OF MOISTURE, A COVER WILL BE INSTALLED OVER THE ECM. IF THERE IS INDICATION OF MOISTURE, THE DEALER WILL REPLACE THE ECM AND INSTALL A COVER OVER THE NEW ECM.

---------------------------------------------------
Item Affected: ENGINE AND ENGINE COOLING:COOLING SYSTEM
Date Announced: 7/13/1994

Description of Recall:
DURING LOW ENERGY FRONTAL IMPACT COLLISIONS, THE FRONT CROSSMEMBER CAN CONTACT THE METAL TUBING PORTION OF THE COOLER HOSE ASSEMBLY; AND/OR THE HOSE ASSEMBLY CAN BREAK AND LEAK OIL ONTO THE HOT EXHAUST MANIFOLD OR THE TURBOCHARGER.

Action Needed To Fix It:
DEALERS WILL INSTALL A PROTECTIVE COVER WHICH WILL PROTECT THE COOLER AND HOSES FROM OTHER STRUCTURAL COMPONENTS IN LOW ENERGY FRONT IMPACTS.

---------------------------------------------------
Item Affected: SERVICE BRAKES, HYDRAULIC:ANTILOCK:CONTROL UNIT/MODULE
Date Announced: 4/4/1995

Description of Recall:
MOISTURE CAN FOLLOW THE ELECTRICAL HARNESS AND ENTER THE PRESSURE SWITCH CONNECTOR CAUSING CORROSION AND MALFUNCTION OF THE SWITCH.

Action Needed To Fix It:
DEALERS WILL INSPECT THE ELECTRICAL CONNECTIONS TO THE ABS PRESSURE SWITCH TERMINALS FOR CORROSION AND INSTALL A SHRINK HOSE TO THE WIRING HARNESS TO AVOID MOISTURE ENTERING THE CONNECTION. PRESSURE SWITCHES WITH CORRODED CONNECTORS WILL BE REPLACED.

---------------------------------------------------
Item Affected: FUEL SYSTEM, GASOLINE
Date Announced: 2/17/1994

Description of Recall:
THE FUEL FILLER AND TANK VENTILATION HOSES MAY DEVELOP CRACKS UNDER THE SECURING HOSE CLAMPS, RESULTING IN FUEL LEAKAGE.

Action Needed To Fix It:
THE FUEL FILLER AND FUEL VENTILATION HOSES WILL BE REPLACED WITH NEW HOSES. THE FIVE SECURING HOSE CLAMPS WILL BE REPLACED BY A NEW TYPE WITH A SHIELD THAT PREVENTS DAMAGE TO THE HOSE WHEN TIGHTENED.










REF: http://www.dealerrater.com/recalls/Saab/9000/

Last edited by BurnsSide42; 10-27-2010 at 06:44 AM.
BurnsSide42 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 10-27-2010, 06:29 AM   #2
Elder
 
BurnsSide42's Avatar
 
Join Date: Oct 2003
Location: South Eastern PA
Posts: 10,049
Post Part 2

1993 Saab 9000 Recalls:

Item Affected: FUEL SYSTEM, GASOLINE
Date Announced: 2/17/1994

Description of Recall:
THE FUEL FILLER AND TANK VENTILATION HOSES MAY DEVELOP CRACKS UNDER THE SECURING HOSE CLAMPS, RESULTING IN FUEL LEAKAGE.

Action Needed To Fix It:
THE FUEL FILLER AND FUEL VENTILATION HOSES WILL BE REPLACED WITH NEW HOSES. THE FIVE SECURING HOSE CLAMPS WILL BE REPLACED BY A NEW TYPE WITH A SHIELD THAT PREVENTS DAMAGE TO THE HOSE WHEN TIGHTENED.

-------------------------------------------------------
Item Affected: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE
Date Announced: 5/12/1999

Description of Recall:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. MOISTURE CAN ENTER THE AIR BAG INFLATABLE RESTRAINT ELECTRONIC CONTROL MODULE (ECM) AND CAUSE CORROSION ON PORTIONS OF THE ECM PRINTER CIRCUIT BOARDS.

Action Needed To Fix It:
DEALERS WILL INSPECT THE EXTERIOR OF THE ECM. IF THERE IS NO INDICATION OF MOISTURE, A COVER WILL BE INSTALLED OVER THE ECM. IF THERE IS INDICATION OF MOISTURE, THE DEALER WILL REPLACE THE ECM AND INSTALL A COVER OVER THE NEW ECM.

------------------------------------------------------
Item Affected: SERVICE BRAKES, HYDRAULIC:ANTILOCK:CONTROL UNIT/MODULE
Date Announced: 4/4/1995

Description of Recall:
MOISTURE CAN FOLLOW THE ELECTRICAL HARNESS AND ENTER THE PRESSURE SWITCH CONNECTOR CAUSING CORROSION AND MALFUNCTION OF THE SWITCH.

Action Needed To Fix It:
DEALERS WILL INSPECT THE ELECTRICAL CONNECTIONS TO THE ABS PRESSURE SWITCH TERMINALS FOR CORROSION AND INSTALL A SHRINK HOSE TO THE WIRING HARNESS TO AVOID MOISTURE ENTERING THE CONNECTION. PRESSURE SWITCHES WITH CORRODED CONNECTORS WILL BE REPLACED.

--------------------------------------------------------
Item Affected: EXTERIOR LIGHTING:BRAKE LIGHTS:SWITCH
Date Announced: 6/22/1994

Description of Recall:
A NUMBER OF BRAKE LIGHT SWITCHES HAVE AN OVAL-SHAPED PISTON WHICH CAN GET STUCK UNDER CERTAIN CONDITIONS. OTHER SWITCHES WERE MOUNTED SO THAT BOTH LOCKING TABS ARE NOT COMPLETELY ENGAGED IN THE MOUNTING BRACKET. IF ONE SIDE IS NOT ENGAGED, THE SWITCH IS MISALIGNED WITH THE PEDAL MECHANISM AND CAN BIND THE PISTON MOVEMENT, WHICH CAN CAUSE THE BRAKE LIGHT SWITCH TO STICK IN THE "OFF" OR "ON" POSITION.

Action Needed To Fix It:
DEALERS WILL INSPECT BRAKE LIGHT SWITCHES. FOR VEHICLES WITH THE OVAL-SHAPED PISTON AND FOR VEHICLES WITH MISALIGNED BRAKE LIGHT SWITCHES, THE BRAKE LIGHT SWITCH WILL BE REPLACED.

--------------------------------------------------
Item Affected: ENGINE AND ENGINE COOLING:COOLING SYSTEM
Date Announced: 7/13/1994

Description of Recall:
DURING LOW ENERGY FRONTAL IMPACT COLLISIONS, THE FRONT CROSSMEMBER CAN CONTACT THE METAL TUBING PORTION OF THE COOLER HOSE ASSEMBLY; AND/OR THE HOSE ASSEMBLY CAN BREAK AND LEAK OIL ONTO THE HOT EXHAUST MANIFOLD OR THE TURBOCHARGER.

Action Needed To Fix It:
DEALERS WILL INSTALL A PROTECTIVE COVER WHICH WILL PROTECT THE COOLER AND HOSES FROM OTHER STRUCTURAL COMPONENTS IN LOW ENERGY FRONT IMPACTS.



1994 Saab 9000 Recalls:

Item Affected: ENGINE AND ENGINE COOLING:COOLING SYSTEM
Date Announced: 7/13/1994

Description of Recall:
DURING LOW ENERGY FRONTAL IMPACT COLLISIONS, THE FRONT CROSSMEMBER CAN CONTACT THE METAL TUBING PORTION OF THE COOLER HOSE ASSEMBLY; AND/OR THE HOSE ASSEMBLY CAN BREAK AND LEAK OIL ONTO THE HOT EXHAUST MANIFOLD OR THE TURBOCHARGER.

Action Needed To Fix It:
DEALERS WILL INSTALL A PROTECTIVE COVER WHICH WILL PROTECT THE COOLER AND HOSES FROM OTHER STRUCTURAL COMPONENTS IN LOW ENERGY FRONT IMPACTS.

-----------------------------------------------------
Item Affected: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE
Date Announced: 5/12/1999

Description of Recall:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. MOISTURE CAN ENTER THE AIR BAG INFLATABLE RESTRAINT ELECTRONIC CONTROL MODULE (ECM) AND CAUSE CORROSION ON PORTIONS OF THE ECM PRINTER CIRCUIT BOARDS.

Action Needed To Fix It:
DEALERS WILL INSPECT THE EXTERIOR OF THE ECM. IF THERE IS NO INDICATION OF MOISTURE, A COVER WILL BE INSTALLED OVER THE ECM. IF THERE IS INDICATION OF MOISTURE, THE DEALER WILL REPLACE THE ECM AND INSTALL A COVER OVER THE NEW ECM.

--------------------------------------------------------
Item Affected: EXTERIOR LIGHTING:BRAKE LIGHTS
Date Announced: 5/20/1994

Description of Recall:
ONE OF THE BULBS IN EACH OF THE BRAKE LIGHT LOWER OUTBOARD LAMP ASSEMBLIES MAY NOT HAVE BEEN PROPERLY WIRED, RESULTING IN IMPROPER TAIL LIGHT ILLUMINATION ON BRAKE APPLICATION. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Action Needed To Fix It:
DEALERS WILL MODIFY THE BRAKE LIGHT OUTBOARD LAMP ASSEMBLIES TO MEET FMVSS REQUIREMENTS.

----------------------------------------------------------
Item Affected: SERVICE BRAKES, HYDRAULIC:ANTILOCK:CONTROL UNIT/MODULE
Date Announced: 4/4/1995

Description of Recall:
MOISTURE CAN FOLLOW THE ELECTRICAL HARNESS AND ENTER THE PRESSURE SWITCH CONNECTOR CAUSING CORROSION AND MALFUNCTION OF THE SWITCH.

Action Needed To Fix It:
DEALERS WILL INSPECT THE ELECTRICAL CONNECTIONS TO THE ABS PRESSURE SWITCH TERMINALS FOR CORROSION AND INSTALL A SHRINK HOSE TO THE WIRING HARNESS TO AVOID MOISTURE ENTERING THE CONNECTION. PRESSURE SWITCHES WITH CORRODED CONNECTORS WILL BE REPLACED.



1997 Saab 9000 Recall:

Item Affected: EQUIPMENT:OTHER:LABELS
Date Announced: 6/30/1998

Description of Recall:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AIR BAG ALERT LABEL ON THE DRIVER SIDE VISOR WAS OMITTED. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Action Needed To Fix It:
OWNERS WILL BE PROVIDED WITH AN ALERT LABEL TO BE INSTALLED ON THE VISIBLE SIDE OF THE DRIVER'S SUN VISOR. IF AN OWNER SO DESIRES, THEIR DEALER CAN INSTALL THE LABEL FOR THEM.



1998 Saab 9000 Recall:

Item Affected: EQUIPMENT:OTHER:LABELS
Date Announced: 6/30/1998

Description of Recall:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AIR BAG ALERT LABEL ON THE DRIVER SIDE VISOR WAS OMITTED. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Action Needed To Fix It:
OWNERS WILL BE PROVIDED WITH AN ALERT LABEL TO BE INSTALLED ON THE VISIBLE SIDE OF THE DRIVER'S SUN VISOR. IF AN OWNER SO DESIRES, THEIR DEALER CAN INSTALL THE LABEL FOR THEM.






REF: http://www.dealerrater.com/recalls/Saab/9000/

Last edited by BurnsSide42; 10-27-2010 at 06:41 AM.
BurnsSide42 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the The Saab Link Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Vehicle Info.
Enter your vehicle information (year, model, mods)
Insurance
Please select your insurance company (Optional)

Log-in


Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 03:29 AM.


Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.5.2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
All content is copyright The Saab Link and it's original authors.


 

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.